Fuel Saver additive patent nano save 20~60% fuel reduce 75~90% air pollution for vehicle
Post Message
-
Fuel Saver additive patent nano save 20~60% fuel reduce 75~90% air pollution for vehicle
-
2018-06-22
-
Chemical, Plastic, Rubber & Environmental Conservation
-
Environmental Conservation Products and Equipment - relative Selling Leads or Buying Leads
-
Taiwan
-
Offer to sell
-
SNT Super Nano Tech series (SFC, EIFT, UKO, SNT) for gasoline vehicles, with the exception of some four-wheel drive vehicles, two turbo-charged engine car fuel efficiency is not obvious, single turbo-charged engine fuel-efficient not good enough, Generally two-wheeled drive transmit vehicles with normal air intake can achieve nearly 100% combustion efficiency and maximum horsepower and fuel efficiency as well as the emission reductions will to the maximum low emission under normal conditions, no damage to components or excessive wear.
A car to fuel, to achieve high standards of fuel efficiency, with the addition of oil fuel smooth, the air intake system and the ignition circuit are all factors that affect the fuel efficiency, non-single conditions can be completed. According to decades of research and development and marketing experience, S.N.T has eliminated most of the barriers that affect fuel economy. In addition to the afore mentioned four-wheel drive vehicles due to unknown structural factors, or dual-turbo engine to achieve a certain rate, the computer sensor to the mixture(oil & air ) too thin will continuous increase in fuel injection and difficult to fuel-efficient, single turbo engine can reach normal air intake car the fuel efficiency can reach about 50-75%. General air intake two wheel drive 1,600cc the following small cars drive in the city , the fuel efficiency will be about 15%, high speed will save about 30% oil, more than 1,800 cc metropolitan area can save more than 20%, high speed can save more than 40%, 3,000cc above The big horsepower, high speed and up to more than 50% fuel-efficient standard level.
In order to achieve the above-mentioned high standard of fuel efficiency, before using S.N.T., First you must examine the characteristics and current situation of the vehicles and decide on the handling methods so as to achieve a multiplier effect.
First、Some brands of vehicles, such as Mitsubishi, most of the lack of air, you must dress up high-flow air filter, or our SNAC (Super Nano Air Converter) - the air can be transformed into Nano molecule when air pass through SNAC, It is easier to help the fuel to burn completely and save more fuel. Therefore, When you use our SNT series product, your car air filter can be replace in high-flow air cleaner or our SNAC at the same time, otherwise it may not be save a lot fuel.
Second、 If car age more than 8 years or driving mileage more than 100,000 km car, as a result of long-term carbon deposition into the plastic style, carbon or carbon dioxide can be a solvent.
The throttle and the combustion chamber (engine) carbon should be completely clean, in order to reduce run-in period, and can quickly reach fuel-efficient.
Third、 Some part of the old car due to aging circuit or contact corrosion, causing in poor ignition spark plug, it has not fuel-efficient, then must be installed our T.S.B.D. Strong electrical appliances, the ignition spark enhancement, to fuel-efficient.
Forth、 Due to the new car engine to be run-in with the burr on the surface of the scrap iron to be removed, so run-in period varies depending on the type of vehicle. SNT fuel-efficient products are generally be used on new cars that have been operating 20,000-30,000 km. Fuel-saving effects can be achieved rapidly within 1,000 km. A few new cars that are not running-in can also run 3,000-5,000 after using SNT fuel-efficient products Km that began to save fuel. However, the new car that reach fuel-efficient immediately, but it can play the best protection, greatly extending vehicle life.
Some vehicles can not automatically adjust the vehicle air intake and fuel injection quantity, can not be fuel-efficient, that is, the computer must be restarted to zero, let it run again to start the learning program, you can restore the auto-tuning function. As the current NISSAN (Nissan) products accounted for the highest proportion of fuel-efficient about 30-50%. Therefore, the installation or use of S.N.T fuel-efficient products, about 500 kilometers, the computer can be zero. In addition to a few other models such as BENZ, to go through the computer to zero, the general vehicle just need to remove the battery positive power off for 10 minutes to return to zero.
However, like Hyundai (Hyundai) after 2010 cars, though known as the entire computer-controlled future car, the computer has been locked, unable to perceive the power of the increase, automatically adjust the appropriate air intake and fuel injection, installation or use SNT fuel-efficient products, can not be function, but futile, but before 2009 car mostly dazzling success.
S.F.C. Advantages and installation methods:
First, the advantages:
S.F.C. high-energy induction and catalytic composite complete combustion device, the volume can be unlimited expansion, due to should be high-flow fuel be decomposed treatment needs of the more processing capacity. Customers can rely on the size of the vehicle, budget and to achieve the horsepower increase and fuel-efficient target selected model. Of course, the larger the volume, the more time of the fuel stays inside the SFC will be decomposed more. The stronger of the horsepower will have the better the effect. Therefore, such as the choice of low-cost cars, small-capacity models will have the lack of power problem, the greater the choice of the better.
Second, the installation method:
(1) Open the hood, search into the pipe fittings and support fixed S.F.C. parts, if can’t find the engine room fuel input pipe, the vehicle must be held high, looking for the exact end of the car into the pipe, decided to install and solid place to set the location.
(2) Open the fuel tank cap, remove the oil pressure, untie into the pipe joints, see the type of inlet pipe (rubber plastic or nylon tube), the size of the inner diameter, the choice of matching joints, access S.F.C to the ends of the inlet pipe. The connector must be securely tightened to prevent oil leakage, S.F.C. firmly fixed in the support area, can not be loosened.
(3) S.F.C. The cylinder is preferably angled at a level of 30-90 ° from the horizontal and the outlet (arrow) is upwards so that the fuel is likely to overflow inside, allowing S.F.C to fully decompose fuel into nano molecules. S.F.C Please avoid placing near in the high temperature and sparks circuit, after installation, do check whether the joint part of the oil spill or loose, in order to ensure safety.
E.I.F.T. The advantages and disadvantages and installation methods (with S.N.A.C more fuel-efficient effect):
First, the advantages and disadvantages:
E.I.F.T. is a high-energy induction complete combustion device, which is different from S.F.C. in that only this device is attached to the inlet pipe surface, that is, by means of high-energy sensing, decompose the fuel through the inlet pipe, and no need to cut off the tubing and fittings, suitable for difficult cases across the tubing. However, E.I.F.T. does not resemble S.F.C.
An internal volume can delay the flow of fuel time, just fear of lack of decompose time, if the proposed installation multiplicative capacity to extend the role of time, also fear limited by tubing length and camber, it is suitable for difficult unlimited installation. To solve this difficulty can be enhanced by the addition of S.N.A.C. (Super Nano Air Converter), which is comparable to the capacity of S.F.C.
Second, the installation method:
(1) Open the hood, find the inlet pipe and easy to clip with the fixed parts, the E.I.F.T. to screw or nylon tape is tightly attached to the inlet pipe and secured to a firm support.
(2) At present, E.I.F.T. has 3.3L and 1.1L two models, if it is difficult to set the pipe bend 3.3L length when, can use 1.1L three generation 3.3.L use, with the same effect.
(3) If the engine room can not find the inlet pipe or the inlet pipe is not long enough to accommodate E.I.F.T., then hold high the vehicle, looking for the appropriate placement from the bottom, and firmly fixed.
S.N.A.C. (air can be decomposed into nano-molecules) advantage and installation method:
First- The advantages:
When the air passes through the SNAC, the air is decomposed into micro-Nano scale and the power is doubled. When these high-energy air enter the engine combustion chamber, they can be further decomposed to atomize the oil molecules to promote complete combustion of the fuel, and the easy installation is advantage too.
EIFT does not have the internal volume like SFC can delay the fuel passage time, resulting in insufficient power, SNAC can make up and assist, if equipped with low-end small SFC, feel less power, the same can be use SNAC to be complemented by addition, coupled with easy installation , All for its advantages.
Second-The installation method:
(1) Open the air filter cover, take the filter, and then choose from one of 32 models SNAC combination to cover 80-100% of the filter area, placed on the air filter, then fixed back into the filter box.
(2) Each time the car is serviced, when you clean the filter, and SNAC can be sprayed on at the same time with a detergent and then use the air gun to blow clean it.
T.S.B.D. Advantages and installation method:
First- the advantages:
T.S.B.D. In addition to the use of the cable system with hundreds of 99.95% high purity thin copper wire composed of high conductivity degrees, the online at the first two ends of the connector on the other end of the deep plating by several rare precious metals, mineral elements
The super alloys, with the regulator, steady flow, enhance the flow of electrons, activation of the old circuit, the ignition spark enhancement 1- 2 times of the effect.
Second- the installation method:
(1) Select the appropriate length of T.S.B.D. One end of the battery is fixed to the negative pole, the other end connected to the engine body screws.
(2) If the battery is placed in the rear trunk or at the rear of the rear cushion, the extended T.S.B.D. at the negative pole of battery, the other end passes around the bottom of the car, or the door edge is properly installed to the engine body, and continued on the top of the screw.
Fuel save-efficient three major elements: 1. Fuel oil to be smooth. 2. Air (adequate intake) 3. Ignition start equipment.
◎ Note:
1. Ignition start system is normal: Check the high-voltage coil and high-voltage lines, Mars plug is not good, damaged or leakage, the clutch is skewed, wear.
2. The oil supply system is normal: check the tubing is twisted, blocked or damaged, resulting in oil supply is not smooth or inadequate.
3. Air supply system is normal: check the intake pipe is smooth, air intake sensing device is normal, the air supply filter has obstruction or failure situation.
※ (SFC allows the fuel molecules to be fully decomposed into nano molecules, that will require more air to help them for burning. It is possible to use a high-flow air filter or our SFAC Super Nano Air Converter to avoid detracting from SFC performance due to insufficient air intake ) (Because using our fuel-efficient products, it need a large amount of air to help the fuel burning completely. If the air filter has stuck too much dirt, it will block the air intake and air input smooth, and the fuel-saving effect will be reduced. So we need to use the air cleaner gun to clean the air filter often. , that can make the air intake more smoothly, especially where the urban air pollution is serious).
4. Mix ratio of oil and air is normal: Too rich or too dilute oil can not be completely combusted, besides causing explosive force, oil is wasted and polluted by waste oil (ideal mixing ratio about 1: 20 diesel / air)
Contact Information
-
Faithtrade Enterprise Co., Ltd.
-
Taiwan
-
Mindy Lin